วันอังคารที่ 11 พฤษภาคม พ.ศ. 2553

DCS-2120

>>> DCS-2120 Basic installation using installation wizard

Step 1. Connect power to the camera and connect the camera to your network. It is recommended to have a DHCP server available on the network (e.g. a router).

Step 2. Insert the installation CD into the CD-ROM drive. Click on Install Software. And then click on Installation Wizard.

Step 3. Go through the installation steps of the Installation Wizard.

Step 4. Launch the Installation Wizard software.

Step 5. The Installation Wizard will discover the camera and show its MAC address and an IP Address (if it has been assigned). If the Installation Wizard does not find the camera, reset it and do a search again.

Step 6. Tick the required camera in the lest and click on Setup button.

Step 7. Go through the Network Camera Installation wizard: Set Administrator password.

Step 8. Set IP address, Subnet Mask, Default Gateway and DNS. Untick the 'Reset IP address at next boot' option.

Step 9. (Optional). Set wireless settings.

Step 10. Apply the settings when finished.

Step 11. Click on Done. Then click on "Link to Selected Devices" button. This will log you into the camera's WEB interface.

-------------------------------------------------
>>> DCS-2120 Motion detection setup for recording?


Step 1 Open Internet Explorer and type in the IP address of the D-Link camera.

Step 2 Click on the Configuration button> Advanced tab> select Motion Detection.

Step 3 Click the New button. A small window will appear on the main screen. You can move this window to the area you wish to monitor. You can resize the window as well.

Step 4 Make sure to name the window, set the sensitivity and percentage for each window, and click the save button. You will get a pop-up telling you the save is completed. Click OK.

Step 5 Follow steps 3 and 4 if you plan to have more than one window enabled for motion.

Step 6 Check the box labled Enable Motion Detection, click Save.

Once you have saved your settings in the web configuration pages you will need to enable the newly created windows in IP surveillance. Follow these steps:

Step 7 Go to Start > Programs > Dlink > IP surveillance > Monitor.

Step 8 Type in your name i.e, admin and password click ok.

Step 9 Click on Function Menu > select Camera Configuration from the list.

Step 10 Make sure you have selected the correct camera name and IP address to enable the motion detection.

Step 11 Under Alert Settings tick the Enable Motion Detection option. Under Recording Settings set how many seconds you want to have recording before and after the event.

Step 12 Click on Save to finish.

Step 13 Click on Function Menu > select Scheduler from the list. Set the Schedule to 'Event Mode'. Tick the Motion Detection option and select the Windows which you want to monotor motions.
Click on Save.

Your motion detection should now be activated. There should be an amber light blinking above the selected camera. Whenever motion is detected you should see a red rectangle flashing on the image.

-------------------------------------------------

Link FAQ for more information of DCS-2120 >>> http://www.dlink.com/
After select Support >> FAQ and select your problem to resolve.

-------------------------------------------------
>>> Remotely view cameras that are behind a router

Please follow the steps in this document:
http://global.dlink.com.sg/FAQ/view.asp?prod_id=1873&question=DCS%2D2120

For each camera that resides behind a router or a gateway, several ports must be forwarded by the router to obtain video and audio (if your camera supports audio). The default ports are:

DCS-2000 and DCS-2100+ cameras:
80 (TCP) HTTP Port (allows access to web-configuration and transmits video if other ports are not forwarded);
5001 (TCP/UDP) Control Channel Port (used to synchronize audio and video);
5002 (TCP/UDP) Audio Channel Port (transmits synchronized audio);
5003 (TCP/UDP) Video Channel Port (transmits synchronized video);

DCS-2120 camera:
80 (TCP) HTTP Port (allows access to web-configuration and transmits video if other ports are not forwarded);
554 (TCP/UDP) RTSP Streaming (used for audio and video streaming to mobile phones);

DCS-3200-series, DCS-5300-series and DCS-6600-series cameras:
80 (TCP) HTTP Port (allows access to web-configuration and transmits video if other ports are not forwarded);
5001 (TCP/UDP) Control Channel Port (used to synchronize audio and video);
5002 (TCP/UDP) Audio Channel Port (transmits synchronized audio);
5003 (TCP/UDP) Video Channel Port (transmits synchronized video);

DCS-G900 camera:
80 (TCP) HTTP Port (allows access to web-configuration and transmits video if other ports are not forwarded);

DCS-950G camera:
80 (TCP) web port(allows access to web-configuration);
5000 (TCP/UDP) AV Control Port (used to synchronize audio and video);
5001 (TCP/UDP) AV Streaming Port(transmits synchronized audio);
5100 (TCP/UDP) IP View Lite Port (transmits synchronized video);

The port numbers will need to be changed in the camera configuration for each additional camera that is added behind the router. Port numbers can be changed from the ADVANCED > NETWORK screen.
NOTE: Some ISP's may block access on port 80. In this case you can setup your camera on a different port (e.g. 8888) and open this port in your router. To access the camera through a port different from default, you need to add colon (:) and the port number to the http:// address (e.g. http://63.116.231.25:8888).



Example: Three cameras are behind a router. The router has a public IP address of 63.116.231.25 and an internal IP address of 192.168.0.1

Camera 1 IP address: 192.168.0.10 Ports: 80, 5001, 5002 and 5003
Camera 2 IP address: 192.168.0.20 Ports: 81, 6001, 6002 and 6003
Camera 3 IP address: 192.168.0.30 Ports: 82, 7001, 7002 and 7003

Each set of four ports must be forwarded to the respective IP address.

To contact these cameras from a remote location (across the Internet), use the PUBLIC IP address of the router along with the appropriate web port. Using the above example:
To contact camera 1 with Internet Explorer, enter http://63.116.231.25
To contact camera 2 with Internet Explorer, enter http://63.116.231.25:81
To contact camera 3 with Internet Explorer, enter http://63.116.231.25:82

*As you can see, when using HTTP port 80, the actual port number does not need to be entered.

These cameras can also be contacted with IP surveillance (included software).

Step 1. Launch the MONITOR application and choose FUNCTION MENU > CAMERA CONFIGURATIONS
Step 2. Enter the routers PUBLIC IP address and port number in the IP address field in the top left corner.
Step 3. Press the INSERT button directly above.
Step 4. Press SAVE.

-------------------------------------------------